Відео

@@tideshiftvisual its not just general durability also fitment. I may not have done a good job in this video of showing that, but besides the duraflex being very thin and brittle, the fitment of it is notably bad and it takes a lot to make it look good

You have to trim out the area with tools like a dremel and test fitment repeatedly till you get it 100%. I recommend looking at the factory bumper corner and following that

Thanks! Does the bumper bolt up anywhere in between the headlights (like the stock one), or is it just secured on the side markers?

Which exhaust I have on the car depends on which video you are asking about. I was using an authentic Mazdaspeed exhaust with a modified turboXS mid pipe up until about a year ago. Anything within the last year is a turbo XS catback with a turbo XS mid pipe

@@rickyse3p i mean on this video at 10:45 min :) ... thank you

Well, besides the fact that the duraflex didnt fit for crap; the point of the video was to show the durability, flexibility, and forgiveness of the urethane the KBD is made of. Shouldn't need to be spelled out...

No such thing as that on a rx8. Priming the oil system at all has zero effect on its ability to start

Failing compression needs a engine rebuild

I sold the last kit several months ago. Since only a dozen people in the community actually put down the $320 for the kit out of hundreds of inquiries over a two year timeframe, I am not sure I will make another batch of kits.

I was wondering that too Mainly the size the and offset, I want the same brakes XD

Reps, wanted to put money towards more important parts of the build than authentic wheels. Vordoven or however the brand is spelled. 18x9.5+35

18x9.5+35 squared setup. Went with reps to save money to spend on other parts of the build. Im not racing on the CR reps, im racing on the motegi traklites with quality tires

@@rickyse3p Pretty neat!! Also, I want to reiterate my last question- I didn't know both from calipers for the 8 were the narrowlite series. You have the 4 piston lightweight kit from Kiesler(?) Right? Thanks in advance!

@@RyuusanFT86 yes they are the calipers included in their brake kit. I put Hawk HT-10 pads front and rear on the car to compliment and round out the setup.

Superlites 👍🏼

I wouldn't really be able to advise you on what would be best in your situation, too many variables. It would be best for you to reach to one of the local or Euro RX8 communities to provide them with more information.

alright, thank you

No.

The video never really showed what's supposed to connect on the other end of the fuse, would you be able to share please? Thank you

Just saw the notification, I am at work rn and I will respond to your message later at my soonest opportunity

No measural benefits. Air passes through the throttle body so quickly that it doesn't really have any measurable effect on air temperatures inside the engine. The point of having the heater go through the throttle body is to help prevent icing on the throttle body in very cold climates.

I believe I have one more kit available. It is the battery holder including the hold down plate, the main positive, the positive from the rear fuse to the battery, two battery grounds, two engine bay grounds, replacement fuse for the EPS, and the mounting hardware for the fuses and battery holder.

How much is it?

And where do I contact you outside of this comment section lol

@@re4per597 you can get in contact with me through my Instagram. More information and pictures can be found on there. ricky.se3p

Like what

Watch my most recent video where i install one on a car for a clearer idea of the power steering positive. It comes from the part of the harness that connects power between the fuse box and starter positive wire.

You should watch the video i did going over things to check when your rx8 wont start

@@rickyse3p got the battery and cables hooked up correctly now I'm at either neutral safety or ignition switch going to test voltage today thanks for getting back to me

@@rickyse3p was wiring in the fuse box, spliced power to the starter relay now it cranks! Looks like its deflooding time

eBay. One of them chipped when washing it once (caught on my wash mitt) and i eventually removed them. They were cheap FRP. I bought some carbon fiber ones i will be putting on the car once i decide if I want to color match them or leave them carbon

Ur not convincing anyone

I haven't been keeping track, I'm doing most of all of the work myself but everything for the most part is custom so if I had to make a guess I'm probably somewhere around $6,000 at the moment

I believe I have one kit remaining

Send me a message on my Instagram, Ricky.SE3P

Check other fuses, make sure everything is running good, make sure your air flow sensor is good, make sure the engine isn't flooded. Look up the deflood procedure just to be certain.

@@rickyse3p OK I just watched ua-cam.com/video/v3uGJGzUYCI/v-deo.html and see why flames come out from one spark plug hole. Its got two plugs per cylinder. I never knew that. So now the term leading and trailing makes sense. OK. so if there's ignition and the only reason the car stopped running was a burnt out trailing coil nearest interior of car, you would say well then car should start. The strange part. Got to car and the 15a fuse for Ecu was blowing. Then I unplugged the bad coil which was blown on the side and the fuse stopped blowing. OK and when scanned all the modules reappeared. Wiring shows they get their power through the engine ECU. OK so then trying to start the car with just 3 coils and it would not start. Out of curiosity I reconnected the blown coil to see the fuse blow again but this time it never. It had blown 5 times before but this time instead of it blowing the coil sat there smoking away like it was about to burst into flames. New coils, leads and plugs. Still it won't start.

@@rickyse3p waited till following morning and then it started. WEIRD

Send it to my Instagram account

Have a few questions I would like to really know in depth about

My Instagram account you can message me. There is one kit left at the moment

@Projectseca ?

I still have like 2 left hmu if you want one